The Gert VGA 666 (6 bits per colour channel, hence 666) is a breakout/add-on board for the Raspberry Pi Model B+ (will not work with Model A/B as the additional GPIO pins on the Model B+ are required). It is an open source hardware design recently released publicly by Gert van Loo who was one of the hardware engineers that was instrumental in the initial design of the original Raspberry Pi (also one of the chip architects on the BCM2835 chip at the heart of the Raspberry Pi) and someone that many of you may have spoken to at Raspberry Jams or on the Raspberry Pi forums.
It is a neat and very useful solution for using a VGA screen/monitor with your Raspberry Pi and is far cheaper than an HDMI to VGA adapter or similar. The VGA connection is driven natively in hardware over the GPIO pins (using a parallel interface) and uses around the same CPU load as the HDMI connection on board. It is capable of displaying 1080p60 VGA video with no CPU load.
It is also possible to drive this interface at the same time as the HDMI connection, so a dual screen setup is also possible. This add-on was not possible on the Model A and B pis, because not all of the required pins had been brought out to the GPIO header. Yet another awesome upgrade that the Model B+ has allowed for!
Gert VGA 666 Kit Contents
- 1 x Gert VGA 666 PCB
- 1 x 40 pin GPIO header connector
- 1 x 15 pin female VGA connector
- 20 x through hole resistors (2*120 Ohm, 3*499 ohm, 3*1kOhm, 3*2kOhm, 3*4kOhm, 3*8kOhm, 3*16kOhm)
- 2 x Pi Supply Stickers
You can find the assembly guide, code repository and further information for the Gert VGA 666 at the following links:
Please note: this add-on on board uses all but 6 of the GPIO pins on the Model B+ Raspberry Pi so it may not be possible to use other add on boards at the same time as the VGA adapter.
Why a kit?
We love electronics kits for a multitude of reasons - they are fun to put together, you get a sense of achievement at the end of it, they are great for learning about soldering and electronics and many many more reasons... At Pi Supply we are quite keen on the whole education and fun aspect of the Raspberry Pi and computing and electronics in general, so we feel that a kit is much more worthwhile to all of our backers. However, you don't need to be a soldering god or an electronics pro to put our kits together - Gert has made this simple enough even for absolute beginners to put together. The images in this project show surface mount resistors, however, for the purposes of the kit we will be supplying all through hole components. There was also a concern about EMC (electromagnetic compatibility) regulations which could cause a problem if made as a fully assembled board. This regulation does not cover home made electronics and so a kit makes more sense for this reason as well.
- VGA 15khz
- scart adapter
- CRT TV
Works as expected. Fast delivery at least in the UK part. Swedish transportation was a bit slower. Connected to a raspberry Pi for outputting VGA 15khz to an New Net City Arcade machine.
As many people I was surprised that it comes as a kit and not preassembled! But anyway it is fairly easy to solder the components. In the end it works as expected. I tested it on a 4:3 LCD and a CRT TV (in combination with an universal scart adapter)
Fun kit to assemble. Picture quality is indeed top notch (outputting 1920x1200@60hz on a "old" Dell 27WFP). Less fun is the bit of flickering I get at the bottom of the screen. I'm looking into it (may be my poor soldering skills or need to try other resolutions or refresh rates).
The card outputs a much better image than I had expected and was not at all as hard to assemble as I had thought. A great cheap way to provide a vga interface, and a fun way to pass an hour (building it). A 19 inch VGA monitor sure beats a 14 inch portable TV. A marvelous little kit.
I also thought that it was assembled, but It was very fun assemble it. http://imgur.com/HGrvYHt http://imgur.com/3C9uaYr http://imgur.com/3C9uaYr http://imgur.com/3C9uaYr